Okidata pacemark 3410 printer manual

Remove the ribbon cartridge. Set the head gap adjusting lever to the range 9 position. Lift and remove the ribbon guide from the two posts. Detach the platen knob 1. Pull the release lever 2 toward the front of the printer. Remove the two cover mounting screws 3 , located at the rear of the printer.

Disconnect the operator panel cable 1 from CN10 2 on the control board. Remove the two mounting screws 3. Remove the upper cover assembly 3. Remove the upper cover assembly. Release the lock of connector CN10 1 and detach the operator panel cable 2.

Remove the main logic board 2. Detach connectors CN 1 and CN 2 from the interface connector board 3. Remove the three mounting screws 4 at the rear of the printer mechanism 5. Remove the printer mechanism 2. Disconnect the two cables 1 from the left side of the power supply unit 2. Remove the four power supply mounting screws 3. Detach the DIN connector 1. Lift the printer unit 2 from the bottom tractor feed unit 3.

Remove the printer unit 2. Remove the two mounting screws 4. Detach the tension spring from the front door assembly. Remove the tension spring 3. Remove the bottom push mechanism 3.

Loosen the two motor screws 1. These bushings should remain in the frame. However, if a bushing must be removed, press the bushings claw which can be accessed from the inside of the side frame. Loosen the three 7 mm line feed motor mounting bolts 1. Move the line feed motor 2 closer to the platen 3 and detach the line feed drive belt 4. Remove the platen assembly 2. Remove the two paper chute springs 1 located on each side of the paper pressure guide 2.

Remove the screw 3 , located on the left side frame of the printer mechanism, directly under the upper tractor shaft. Remove the two ribbon cartridge bracket mounting screws 1. Remove the ribbon cartridge bracket 2. NOTE: When assembling, the tabs 3 on each side of the ribbon cartridge bracket must slide into the slots on the printer mechanism. Remove the two fan mounting screws 2. Remove the fan 3.

Detach the printhead 2. Remove the ribbon cartridge bracket 3. Loosen the two mounting screws 1 , detach the tabs from the frame and remove the cable holder 2. The tabs must be accessed from the bottom of the printer mechanism.

Remove the head cable assembly 2. Loosen the slider mounting screw 1 and push it towards the back of the printer. Remove the belt clamp mounting screw 2 and detach the belt clamp 3. Remove the ribbon feed assembly 3. Loosen the two belt pulley bracket mounting screws 1. While pushing the belt pulley bracket to the left A , temporarily tighten the two screws. Remove the printhead 2. Remove the space motor assembly 3. Remove the mounting screw and detach the connector clamp 1. Detach the head cable assembly 2 from the carriage.

Detach the paper bail springs 1. NOTE: The right and left bail arm springs are different; be careful to install them properly. Remove the idler gear 2.

Remove the lower center guide 1. A Pacemark Replacement Printhead Kit includes the items listed below. Page 1. Remove the ribbon cartridge and ribbon guide 3.

Remove the ribbon protector 3. Remove the upper cover 3. Set the printhead gap lever to position 1. Page 7. Fill out the Customer Warranty Extension Card if applicable. When changing paper paths or paper type, be sure to adjust the printhead gap lever. This blue lever is located on the right hand side of the printer.

Page 90 days from the date of the printhead repair. Any Authorized Pacemark Okidata Repair Center will honor this extension when properly dated and signed by a certified repair technician.

Please retain this for your records. Page Line Feed Belt Tension 3. Tighten the three mounting bolts. This will help you move through the menu. To print the Menu, follow this procedure. Verify that continuous feed paper is installed. Page Menu Settings 7. Group Item Setting Page Top Of Form These sets contain special characters used in foreign languages. The Publisher set includes special printing symbols.

Page Page Width Changing this setting to YES allows printing to occur closer to the bottom edge of the paper. Print Registration 0. When the printer advances to the next page, it stops at the top of form. The Pacemark can store a different top of form position for the three standard paper feed paths top, rear, and bottom.

Page Paper Park 4. Lower the paper support. Forms Tear Off advances the paper from the initial printing position to the tear off position. Page 3. The paper will retract to the Top of Form position. Release TEAR. The paper advances to the tear bar position. Power OFF the printer. Small pieces of paper can cause paper jams. Remove the platen knob. Be sure to place it in the shipping container.

Pack the unit, using the materials from Step 1. Make sure the printhead is secured so it will not move during shipment. Okidata strongly encourages you to report any problems you may encounter when using the materials of this training kit. Please be as specific and detailed as possible.

Your comments, suggestions, and criticisms are used to update and revise training kits. This service is available to all Okidata Certified Service Technicians. Okilink II provides troubleshooting and service information. Technicians can download files, ask questions of Okidata's technical support personnel, and participate in round table discussions about Okidata products and services.

Page Troubleshooting Tips 4. Has the ribbon been installed properly? Okidata Pacemark Service Manual pages. Okidata microline personal printer user's manual pages. The software described in this manual, as well as the manual itself, are furnished under the terms and conditions of a license agree- ment. The software consists of software options which are separately licensed.

For additional information about the printer, see the Pacemark Printer Handbook, which came with the printer. V Use these printer settings Sometimes the printer settings for the DX10 system differ from those for the Eagle system and are indicated as such in this column. The printer menus are directories of printer features. You can also use the Pacemark Triad Default Printer Settings table on page 5 to identify printer menus, and as a reference to the Triad default printer settings. Pacemark Triad Default Printer Settings V Call the Triad Advice Line at 1 Print page 1 Print document 9 pages.

Rename the bookmark.